total amount of CO2 gas
Structure of an automobile
Chassis
Mg-Zn-Zr alloy
Magnesium alloy + Zr
Grain refinement
Mg-Ce alloy
Precipitation Ce on GB at high temp.
High creep strength
Engine parts(Introduction)
Basic engine part
High engine weight ratio
Require strength
Require heatresistance
Require easy casting property
1. 목적
Mg-Ca alloy의 열처리 시간에 따른 기계적 특성 및 내식성을 평가한다.
2. 이론조사
2.1 Mg-Ca alloy의 일반적인 특성
Mg-Ca 합금은 Ca이 첨가됨에 따라 결정립의 크기가 작아지는 특성을 보이면서 경도, 강도가 강해진다. 또한 Mg2Ca가 Mg와 갈바닉 전지를 형성하여 합금의 내 부식성을 증가시킨다.
1. Introduction
1) Definition of preservation and food-spoilage micro-organisms
Food preservation is the process of treating and handling food to stop or greatly slow down spoilage (loss of quality, edibility or nutritive value) caused or accelerated by micro-organisms. Some methods, however, use benign bacteria, yeasts or fungi to add specific qualities and to preserve food (e.g., cheese, wine
the short
length of the fins laterally, rather than longitudinally down
the long length.
Focused on placing the jets at the end of the fins and using them to induce air flow longitudinally down the length of the fin
The primary jet to emanate directly through the heat sink base and entrain and expel air laterally over the height of the fins through a matrix of synthetic jets
3. 증기 터빈의 효율 향상 방안
그림3-1. Steam Path Loss[1] 그림3-2. Leakages[1]
위에서 그림3-1은 스팀 터빈이 구동하는 중에 Steam Path에서 발생되는 손실 요인들에 대해서 나타내고 있다. 손실 중 50%로 가장 많은 부분을 차지하고 있는 것은 누설 손실로, 세부적으로는 블레이드 상단으로 누설
잎을 꽂는다.
② 아크릴 봉 쪽에 100mg의 분동 1~2개를 걸어서 한 눈금에 대한 질량을 구한다.
③ 10~20분간, 마다 물의 감량에 따른 지시침의 흔들림을 관측하고, 눈금을 읽는다.
④ 감수량과 시간과의 관계를 나타낸다.
⑤ 나뭇잎의 면적을 그래프용지에 나타내어 대략적인 잎의 면적을 구한다.
- -
Generation of Steam from a Waste Heat Boiler
야금법의 용광로나 화석연료기관의 작동에서 생성되는 배기가스들은 고온상태로 배출된다. 이때 이러한 고온상태의 배기가스들을 이용하여 가열하는 기관을 Waste Heat Boiler라 한다. 배기가스를 그냥 배출시킬 경우 상당한 열이 낭비되므로 이를 재활용하여
resistance)
표면저항은 보통 단위 Ω/□로 표시된다. 일반적인 선 저항은 두 개의 probe로 임의의 거리에 대한 저항을 측정하지만, 표면저항의 경우에는 동일한 간격의 4개의 탐침으로 측정하게 된다. 이때 쓰이는 Probe가 Four point probe이고, 보통 탐침은 1mm간격으로 일렬 구성된 probe를 사용하며, 4개의 탐침으
mg/ml 농도로 첨가한다.
② 충분히 섞어 젤을 굳히는 판에 붓고 식을 때까지 기다린다. (굳힐 때는 comb를 끼워서 well을 만든다.)
③ 전기 영동 tank에 1 X TAE를 넣은 후 gel을 넣는다. (이 때 TAE buffer는 gel이 살짝 잠길 정도로 붓는다.)
④ 2 µl의 100bp DNA ladder를 loading하여 DNA size marker로 사용한다.
⑤ 확인